- Open Access
- Total Downloads : 223
- Authors : Anjaly R Krishnan, Rahul Leslie, Unnikrishnan S
- Paper ID : IJERTV4IS080140
- Volume & Issue : Volume 04, Issue 08 (August 2015)
- DOI : http://dx.doi.org/10.17577/IJERTV4IS080140
- Published (First Online): 13-08-2015
- ISSN (Online) : 2278-0181
- Publisher Name : IJERT
- License: This work is licensed under a Creative Commons Attribution 4.0 International License
Damage Detection in Bowstring Girder Bridge using Dynamic Characteristics
Anjaly R Krishnan |
Rahul Leslie |
Unnikrishnan S |
PG Student |
Associate Director |
Assistant Professor |
Department of Civil Engineering |
DRIQ Board, PWD |
Department of Civil Engineering |
Sree Buddha College of engineering |
Thiruvananthapuram, India |
SreeBuddha College of engineering |
Alappuzha, India |
Alappuzha, India |
Abstract – Damage detection in civil infrastructure has gained greater attention for decades. Mode shape curvature method is a common damage detection technique based on Vibration based damage detection method. In this work we applied this method to a Bowstring girder bridge to locate the damage. Here we applied artificial damage to various members of the bridge model created using staad pro v8i.By changing damage severity at three different cases were also studied in this paper. The mode shape curvature for both intact and damaged structure were calculated. Damage location can be obtained with the help of central difference approximation. The absolute modal curvature was compared between the three damage cases. From the results, the absolute changes in modal curvature are localized in the region of damage and hence Mode shape curvature method is appeared to have potential in damage detection in this bridge.
Keywords: Damage detection, mode shape curvature method, Bowstring Girder Bridge
-
INTRODUCTION
Civil engineering structures are prone to damage and deteriorations during their life time. Damage accumulates in structures due to environmental loadings such as wind, snow, and ice. These environmental factors can lead to fatigue, corrosion in structural steel and material deterioration in concrete .Damage existence in civil structures causes a reduction in their capacity to carry loads. Undetected damages can lead to catastrophic failure of the structure as a whole or some of its elements. Reliable nondestructive damage detection is crucial to maintain safety and integrity of these structures. The use of dynamic system parameters in damage detection has become an important topic. In the most general terms, damage can be defined as changes introduced into a system that adversely affects its current or future performance. Damage can be identified by making comparison between two different states of the system, one of which is assumed to represent the initial and often undamaged state (1). The idea of vibration based damage detection (VBDD) is to measure the dynamic characteristics of the structure such as natural frequencies, damping and mode shapes for comparing them with later measurements. Then comparing these characteristics, damages can be identified.
In recent years, many researchers were interested in developing methods that can detect the existence and location of damage. Some VBDD methods are based on changes in natural frequencies, curvature /strain modes, modal strain energy .Among the above said modal properties, natural frequency is widely used as it can be easily measurable. But they cannot provide sufficient information to locate the damage since they are global properties of the system.
To overcome this drawback mode shapes have been used for identifying the damage location (9). Changes in mode shapes are more sensitive to local damage when compared to changes in natural frequencies. However, using mode shapes also has some drawbacks. First, damage is a local phenomenon and may not significantly influence mode shapes of the lower modes that are measured from the vibration tests of a large structure. Second, the extracted mode shapes are affected by environmental noise from ambient loads or inconsistent sensor positions. Also, an accurate characterization of the damage location the displacement mode shapes requires measurements in many locations (10).
-
THEORETICAL BACKGROUND
-
Modal curvature based damage detection method Mode shape curvature for the bridge for both intact and damaged condition can be obtained from the displacement mode shapes. Derivative of mode shape is curvature.
Pandey, et al. (8) Stated that, the mode shapes of a damaged and the corresponding undamaged structure are identified, the curvature at each location i on the structure is numerically obtained by central difference approximation
ij " = ( (i+1) j – 2 ij + (i-1) j ) / h 2
Where, i is the node number, j is the mode shape number and h is the distance between the measurement points i+1and i- 1.
The location of the damage is then identified by the largest computed absolute difference between the mode shape curvatures of the damaged and undamaged structure, as follows
ij" = ij d" – ij ud"
Where (ij,d) and (ij,ud) is the central difference approximation of damaged and undamaged structure respectively.
-
-
NUMERICAL ANALYSIS AND MODEL
A Bowstring girder bridge model is used in this work. The model was created using STAAD Prov8i. The modelled bow string girder bridge is shown in figure 1. It has a span of 53 m and width of 12m. The material considered is with Modulus of Elasticity, E = 2.17 X 10 7kN/m2, Poissons ratio
= 0.17.
Both intact and damaged structure is created. Here one of the Dynamic characteristics i.e. mode shape is varied by changing the physical property stiffness. In this work damage is introduced all the structural elements of the bridge.
0.006
0.004
0.002
0
curvature difference
0.002
0.001 90
80
0
0 20 40 60 70
SPAN
Curva
ture diffe
rence
Fig 2: damage at arch rib element 10, mode 4
90
80
70
0 20 40 60
Fig 3: Damage at arch element 10, mode 8
Fig 1: Bridge model created using STAAD Pro V8i
Table 2: Mode shape curvature difference at longitudinal girder element 1 Longitudinal girder
mode shape curvature difference
In the analysis, 48 mode shapes were obtained in the STAAD output. Both vertical and horizontal mode shapes can be used to locate the damage (11). In this work only vertical mode shapes is using for damage assessment.
Here three different damage severity cases were studied. By reducing youngs modulus by 90%, 80% and 70%. These three different severity conditions were applied to all the elements i.e. arch rib, longitudinal girder, hangers, cross girder.
-
RESULTS AND DISCUSSION
Mainly two mode shapes are considered for this study, mode 4 and mode 8.The following graph represents the curvature difference between different damage conditions. From that graph we can observe that 90% reduction in youngs modulus has the highest peak followed by 80% and 70% respectively.
Arch rib element 10
mode shape curvature difference
mode number
damage (E reduced by)
4
8
90%
80%
70%
0.00164
0.00099
0.00067
.00425
0.00329
0.00241
Table 1: Mode shape curvature difference at Arch rib element 10
0.006
0.004
0.002
0
-0.002
mode
number damage (E reduced by)
90% 80% 70%
4 0.00522 0.0028 0.00184
8 0.00712 0.0038 0.00247
curvature difference
0 20 40 60
90 80 70
Fig 4: Damage at longitudinal girder element 1, mode 4
0
20
40
60
90
80
70
0.008
0.006
0.004
0.002
0
Fig 5: Damage at longitudinal girder element 1, mode 8
Table 3: mode shape curvature difference at cross girder element 8
0.0003
0.0002
0.0001
0
-0.0001
curvature difference
0 2
0 4
0 6
0
90 80 70
Fig 8: Damage at hanger element 1, mode 4
curvature difference
0.001
0.0005
Cross girder
number
damage (E reduced by)
90%
80%
70%
4
0.0255
0.0114
0.00678
8
0.0582
0.0207
0.01195
mode shape curvature difference
mode
90
80
0
0
20
40
60
70
0.03
0.02
0.01
0
-0.01
0.08
0.06
0.04
0.02
0
-0.02
curvature difference
0 2
0 4
0 6
0
90 80 70
Fig 6: Damage at cross girder element 8, mode 4
0 2
0 4
0 6
Curvature difference
0
90 80 70
Fig 7: Damage at cross girder element 8, mode 8
-0.0005
Fig 9: Damage at hanger element 1, mode 8
-
RESULT AND DISCUSSION
The method of mode shape curvature method is used in bowstring girder bridge to locate the damage. The main objective is to use the changes in the mode shapes curvature to detect the occurrence and location of structural damage. In this study, three cases were studied i.e. 90%, 80% and 70% reduction in youngs modulus. Here mainly mode 4 and mode 8 are considered since these two modes was more capable for locating the damages. From the graph, we can conclude that highest peak point indicate the location of damage in the bridge. And also from the table, it is clear that higher the peak value means more severity in damage. All the elements were taken for the study, certain elements damage location is not accurate comparing to the other results. Further study is needed in damage location in certain elements, i.e. first element of hangers for this bridge.
-
REFERENCE
-
V. B. Dawari, G. R. Vesmawala , Structural Damage Identification Using Modal Curvature Differences, IOSR Journal of Mechanical and Civil Engineering, PP: 33-38
-
H. M. Abozeid, M. N. Fayed , S. M. Mourad , A. H. Khalil , Damage detection of cable-stayed bridges using curvature change in modal
Hanger
mode shape curvature difference
mode
number
damage (E reduced by)
90%
80%
70%
4
0.00022
0.00018
0.00010
8
0.00082
0.00066
0.00052
Table 4: mode shape curvature difference at hanger element 1
mode shapes , International Conference on Bridge Management Systems Monitoring Assessment and Rehabilitation, March 2006,Egypt
-
A.H. Gandomi, M.G. Sahab, A. Rahaei and M. Safari Gorji, Development in Mode Shape-Based Structural Fault Identification Technique, World Applied Sciences Journal 5 (1): 29-38, 2008
-
Ahmed A. Elshafey1, H. Marzouk and M. R. Haddara, Experimental Damage Identification Using Modified Mode Shape Difference, J. Marine Sci. Appl. (2011) 10: 150-155
-
Mohamed Abdel-Basset Abdo, Reliability of Using Curvature Techniques in Structural Damage Detection, Journal of Engineering and Applied Sciences, Vol:1, (2014), Pages: 112
-
Kazuma Nunoa,b, Damage detection of a steel truss bridge using frequency response function curvature method, ISRN
-
E.V.V.Ramanamurthy , K. Chandrasekharan, Nishant Gaurav
,Damage Identification and Location by Using the Frequency Response function in a Composite Cantilever Beam , 3rd World Conference on Applied Sciences, Engineering & Technology 27-29 September 2014
-
Ramanamurthy E.V.V, Chandrasekaran K., Damage Detection in Composite Beam Using Numerical Modal analysis, International Journal on Design and Manufacturing Technologies, Vol.2, No.1,
July 2008
-
Pandey, A.K., Biswas, M. and Samman, M.M. 1991. ''Damage Detection from Changes in Curvature Mode Shapes,'' Journal of Sound and Vibration, 145(2):321332
-
J.T. Kim and N. Stubbs, Crack detection in beam-type structures using frequency data, Journal of Sound and Vibration, 259(1), 2003, 145- 160.
-
A.K. Pandey, M. Biswas and M.M. Samman, Damage detection from changes in curvature mode shapes, Journal of sound and vibration, 145(2), 1991, 321-332
-
Quan, Q. and Weiguo, Z., 1998. Damage Detection of Suspension Bridges, 16th International Modal Analysis Conference (IMAC), California, USA, Feb. 2-5, V. 2, pp. 945-951