Squeal Analysis of Disc Brake Rotor using Finite Element Approach

DOI : 10.17577/IJERTV6IS020221

Download Full-Text PDF Cite this Publication

Text Only Version

Squeal Analysis of Disc Brake Rotor using Finite Element Approach

Anjish M George

M Tech Machine Design

Sree Narayana Institute of Technology Adoor, Kerala

Nithin Prasad

M Tech Machine Design

Ramu S

Dept. of Mechanical Engineering Sree Narayana Institute of Technology

Adoor, Kerala

Sree Narayana Institute of Technology Adoor, Kerala

Abstract Brakes are one of the important components in safety as well as performance of automobiles. From the time of emergence of automobiles, developers has been mainly focused on increasing braking power as well as reliability. As per the complaints from customers as well as high warranty costs, disc brake squeal noise is a complicated phenomenon in which automobile manufacturers have ever confronted. The finite element method (FEM) has become the preferred method in recent years, due to the high costs in performing experimental methods. In this study, the modeling of the disc brake rotor is been done on Solid works and later modal analysis is performed using ANSYS Workbench 15.0. The brake disc squeal is checked for materials like Aluminium, Grey Cast Iron and HSS M42 and material with least squeal is determined and is highly recommended.

Keywords Brake Squeal; Disc brake; Modal analysis; Natural frequency

issue is not good. For analyzing variety of structural as well as thermal problems of braking system, now a days FEM has been widely used. Modal analysis is applied to the brake disc in order to analyze the squeal for different materials. This modal solution approach is based on non-linear contact analysis which helps in identifying design problems in development stages that leads to brake squeal.

  1. INTRODUCTION

    In todays automotive market, the competition is rising day by day for achieving better performance in vehicles. The disc brake is a device used for stopping or slowing the wheel rotation. Brake disc is generally made of Aluminum, Grey Cast Iron, and HSS M42 [1]. The brake pads produced are subjected to mechanic, hydraulic, pneumatic as well as electro-magnetic forces against two sides of the rotor disc. This friction enables the vehicle to stop or to slow with the help of disc and attached wheel arrangement. Kinetic energy of the moving member is been dissipated as heat energy by means of braking system. If the brake becomes too hot, its efficiency gets reduced gradually. This phenomenon is called as brake fade. These brakes fade later leads to brake squeal and produce high frequency noise above 1 kHz, also known as squeal.

    Squeal sound is generally defined to be in the range between 1 kHz and 15 kHz. This range is divided into low frequency domain (1 ~ 3 kHz) and high frequency domain (5 kHz and over). By the introduction of modifications on caliper stiffness, mounting brackets and rotor geometry, brake squeal noise can be considerably reduced. Mostly, trial and error method was performed by brake pad manufacturing companies to find out the squeal problem. Suppliers had to depend on experimental testing methods in order to solve squeal and related problems. This method is costly as well as time consuming one. Thus this approach of addressing the

    Fig 1: Disc Brake assembly [7]

  2. ASSUMPTIONS FOR MODAL ANALYSIS

    For performing modal analysis following assumptions are considered,

    • Loads are not considered.

    • Pressures are not considered.

    • Damping effects are not considered.

    • Considering pre-stress effects.

    1. MATERIAL PROPERTIES

      The materials properties and chemical compositions are discussed below.

      1. Grey Cast Iron: Carbon 3 to 3.5% Silicon 1 to 2.75% Manganese 0.4 to 1%

        Phosphorous 0.15 to 1%

        Sulphur 0.02 to 0.15%

        Remaining portion is Iron. The Grey color is due to the fact that the carbon has been present in the form of free Graphite. It has got low Tensile Strength, high compressive strength and no ductility. This can be easily machined. Grey Cast Iron castings are widely used in machine tool bodies, Automotive Cylinder blocks, heads, housings etc. Its melting point is 1300oC.

      2. Aluminum:

        Copper 3.5 to 4.5%

        Manganese 0.4 to 0.7%

        Magnesium 0.4 to 0.7%

        The remaining content is Aluminium. It is a white metal produced from its oxide by means of electrical process, which has been prepared from Bauxite. It is a light metal having specific gravity of 2.3 and melting point 658oC. The tensile strength of the metal varies from 90 MPa to 150 MPa. It has got good electrical conductivity and widely used in overhead cables.

      3. HSS M42:

    Carbon 0 to 1.10%

    Chromium 0 to 3.75%

    Molybdenum 0 to 9.5%

    Vanadium – 0 to 1.15%

    Cobalt 0 to 8%

    It is widely used because of its higher red-hardness when compared to other conventional high speed steels and applicable in metal manufacturing process.

    TABLE I PROPERTIES OF MATERIALS

    PROPERTY

    Grey Cast Iron

    Aluminium

    HSS M42

    Density

    (kg/m3)

    7200

    2690

    7900

    Youngs Modulus

    (GPa)

    110

    68.9

    210

    Poissons

    Ratio

    0.28

    0.36

    0.29

  3. MODELING OF DISC BRAKE

    Fig 2: Model of Bajaj Pulsar Disc Brake

    The figure shows the solid model of the disc brake by using SOLID EDGE by considering the BAJAJ Pulsar disc brake dimension.

  4. ANALYSIS OF DISC BRAKE

    1. MODAL ANALYSIS

      The natural frequencies of disc rotor for grey cast iron, Aluminium and HSS M24 are analyzed at six different modes and a comparative study is made among these three materials. Material which generates least squeal is found out and recommended.

    2. RESULTS

      1. GREY CAST IRON

        MODE 1

        MODE 2

        MODE 3

      2. ALUMINIUM

        MODE 6

        MODE 4

        MODE 5

        MODE 1

        MODE 2

        MODE 3

      3. HSS M42

    MODE 6

    MODE 4

    MODE 5

    MODE 1

    MODE 2

    MODE 3

    MODE 4

    MODE 6

    TABLE II COMPARISON OF RESULTS

    MODES

    MATERIALS AND MODAL FREQUENCIES

    Grey Cast Iron

    (Hz)

    Aluminium

    (Hz)

    HSS M42

    (Hz)

    1

    2114

    2296.6

    2394.9

    2

    2143.1

    2329.6

    2427.3

    3

    2157.4

    2342.3

    2444.8

    4

    2185.9

    2371.1

    2478.5

    5

    2208.3

    2393

    2504.9

    6

    2271.7

    2460.9

    2575.5

    From the above table we can see that Grey Cast Iron has low squeal compared to Aluminium and HSS M24. Minimum squeal was obtained at mode 1, i.e. 2114 Hz for cast iron and 2296.6 Hz for Aluminium and 2394.9 Hz for HSS M24.and Maximum squeal was obtained at mode 6, i.e. 2271.7 Hz for Cast Iron and 2460.9 Hz for Aluminium and 2575.5 Hz for HSS M24.

    MODE 5

  5. CONCLUSION

In the present study we have conducted a modal analysis on disc rake of pulsar bike at 6 different modes and we analyses the natural frequency at each modes for the three materials. We understand that Grey Cast Iron has low squeal compared to other 2 materials. Minimum and maximum squeals were obtained at mode 1 and mode 6 respectively. The obtained squeals were with in the low squeal frequency range (1 KHz to 7 KHz). Since Aluminium has better stress withstanding ability than other two materials [1], Aluminum can be selected as the suitable material for disc brake.

ACKNOWLEDGMENT

The journal titled SQUEAL ANALYSIS OF DISC BRAKE ROTOR USING FINITE ELEMENT APPROACH

was presented in partial fulfillment for the award of the degree of Master of Technology in Mechanical Engineering. I express my deep gratitude towards Mr. RAMU S, Assistant Professor of Mechanical Engineering Department for his valuable advice and guidance. Also express my gratitude towards my colleague NITHIN PRASAD for his valuable advices and support.

REFERENCES

  1. Praveena, Lava Kumar, Sreekanth Reddy Modeling and Structural Analysis of Disc Brake ISSN: 2319-8753 Vol. 3, Issue 10, October 2014.

  2. Yaswanth Moogilipuri Structural and Thermal Analysis of Vented and Normal Disc Brake Rotors IJMETMR ISSN No: 2348-4845 April 2015.

  3. K. Sowjanya, S Suresh Structural Analysis of Disc Brake Rotor International Journal of Computer Trends and Technology (IJCTT) volume 4 Issue 7July 2010 ISSN: 2231-2803

  4. Nouby and K. Srinivasan Parametric studies of disc brake squeal using finite element approach Journal Mechanical December 2009, No.29, 52-66

  5. Ali Belhocine, Abd Rahim Abu Bakar, Mostefa Bouchetara. Structural and contact analysis of disc brake assembly during single stop braking event American Journal of Mechanics and Applications 2014; 2(3): 21-28 published online August 2012

  6. Huynh Le Hong, Thai Phan Thanh Nhan Analysis stability of brake related to squeal by finite element method grant journal ISSN 1805-062x, 1805-0638 (online), ETTN 072-11-00002-09- 4.

  7. G Babukanth & M. Vimal Teja, Transient Analysis of Disk Brake By using Ansys Software International Journal of Mechanical and Industrial Engineering (IJMIE), ISSN No. 2231

6477, Vol-2, Issue-1, 2012.

Leave a Reply